news

news

Casing Pressure vs Tubing Pressure

11.19.2026

Walk up to a producing well and you will usually find more than one pressure gauge on the tree. Two of the most read are tubing pressure and casing pressure. They sit a few feet apart on the same wellhead, yet they describe two different systems: one is a flow measurement of what the reservoir is delivering through the production string, the other is an integrity measurement of the sealed annulus around it. Understanding casing pressure vs tubing pressure is a basic production skill, because the relationship between the two readings — not either number alone — is what tells an operator whether the barriers downhole are still holding.

 

Two Gauges, Two Different Systems

Both readings arrive in psi or kPa from gauges mounted a few feet apart on the same tree, which is the source of most confusion. They hang off different bodies: the casing head sits lower, carrying the casing hangers and a valve for each annulus; above it the tubing head suspends the tubing string and provides a tubing outlet to the tree and a separate annulus outlet giving access to the tubing-casing annulus (TCA).

Table 1 — Casing pressure vs tubing pressure at a glance
Aspect Tubing pressure (TP / THP) Casing pressure (CP / CHP)
What it measures Pressure of fluid inside the tubing string Pressure in the tubing-casing annulus
Where it is read Tubing head outlet / flow wing upstream of the choke Annulus outlet on the tubing spool or a casing head valve
Common abbreviations TP, THP, FTHP (flowing), SITHP (shut-in) CP, CHP, SCP (sustained)
Normal reading Varies with rate, choke, GOR and water cut Near zero, or a stable designed value
What it tells you Inflow performance, nodal analysis, artificial lift Barrier integrity, annulus management, leak diagnosis
Governs pipe design load Burst (internal yield) for tubing Collapse for casing

On a multi-string well the term ‘casing pressure’ is ambiguous — a completion may have surface, intermediate and production casing annuli, each with its own gauge. Field reports should name the string or annulus (A, B, C) behind every value.

 

What Tubing Pressure Actually Represents

Tubing pressure is a flow measurement sitting at the end of a chain of pressure losses: reservoir pressure, less the hydrostatic head of the produced fluid column, less friction along the tubing, less the drop across the choke, gives the flowing tubing head pressure (FTHP). A high FTHP therefore does not automatically mean a strong well — a light-oil or gas well through a small choke can show high tubing pressure while the reservoir is already depleted, and a heavy-fluid water-drive well may show a modest reading.

Shut-in tubing head pressure (SITHP) is generally more informative than a flowing value. Once the well stabilises after shut-in, SITHP approaches reservoir pressure minus the hydrostatic head of the fluid in the tubing. A slow rise to a stable plateau is normal, while a plateau well below expectation points to depletion, a blocked tubing or a partially closed downhole barrier. A sudden flowing-pressure drop at unchanged choke position can also mean a restriction has cleared or a tubing joint has begun to leak.

 

What Casing Pressure Actually Represents

Casing pressure is an integrity measurement. In a properly completed well the annulus is a sealed volume and its pressure should be predictable from the design. Three steady states are legitimate: near zero, when the annulus is liquid-filled with the level below the wellhead or has been bled to atmosphere (common on land wells with a set packer); a stable positive pressure, such as a gas-lift annulus carrying injected gas or a thermal well with an insulating fluid and expansion allowance; and a shut-in pressure that stabilises after a thermal transient.

What is not legitimate is a pressure that keeps climbing or rebuilds after being vented. The main sources are a tubing leak at a connection, packer or seal failure, gas migration through cement, thermal expansion of trapped annulus fluid, and pressure trapped during cementing. Distinguishing these is a diagnosis task: a thermal effect settles with temperature, while a sustained source keeps returning.

 

Sustained Pressure and the Shape of the Response

Sustained casing pressure (SCP) is annular pressure that rebuilds after being bled down and shut in; it is defined by that behaviour rather than by a specific number. It is managed under API RP 90-1 for offshore wells and API RP 90-2 for onshore wells, which classify annular pressure by source — thermal, operator-imposed, trapped during cementing, or formation-induced — and treat each category differently. A thermal pressure that stabilises within the design allowance is monitored; a formation-induced pressure that continues to climb calls for diagnosis and a documented remediation plan.

One practical caution: the screening threshold is jurisdictional. Many operators compare annular pressure with a percentage of the casing minimum internal yield or burst rating, but the actual limit comes from company policy and the regulator, and it varies by region and well type. A single percentage should not be carried across a portfolio.

Table 2 — Common causes and how they behave
Cause Typical behaviour Category
Thermal expansion of trapped fluid Rises with temperature, then stabilises Thermal / APB
Designed gas lift or annulus injection Stable at an intended operating value Operator-imposed
Tubing connection or wall leak Tracks tubing pressure changes Sustained — integrity
Packer or seal failure Rebuilds after bleed-down Sustained — integrity
Gas migration through cement Slow, persistent rebuild Sustained — integrity
Pressure trapped during cementing Present from completion, may fade Trapped

 

Why the Distinction Matters for Pipe Selection

The readings also drive the specification of the tubulars themselves. Burst (internal yield) normally governs tubing, sized against maximum shut-in surface pressure with a gas column plus any injection or stimulation pressure; collapse is still checked for deep-set packers or workovers that leave the annulus empty. Casing reverses the priority, with collapse governing in most designs. Both collapse and burst ratings are calculated under API TR 5C3 and quoted in the pipe specification under API Spec 5CT / ISO 11960, so the operating pressure history of a well is a direct input to grade, wall thickness and connection choice.

Where a well carries known surface pressure together with H2S or CO2, the load cases and the corrosive environment are sent together so a grade, wall and connection can be proposed against the applicable specification level — for example sour-service grades such as API 5CT C110 for sour service. For the broader range of strings and connections see the API 5CT casing product range, and for a representative tubing string the API 5CT N80 production tubing page.”

 

API 5CT Casing and Tubing Test and Inspection

If you are selecting casing and tubing for a well with known surface pressure and a defined H2S/CO2 environment, send the load cases and the required specification level. A grade, wall thickness and connection proposal can then be returned against the applicable API 5CT / ISO 11960 requirements instead of a generic catalogue choice.

 

FAQ

What is the difference between casing pressure and tubing pressure?

Tubing pressure is measured inside the production tubing and reflects the fluid being produced; casing pressure is measured in the annulus between the tubing and the casing and reflects the condition of the barriers around that conduit. Tubing pressure follows reservoir and flow behaviour, casing pressure should stay independent of it. In a healthy completed well the two readings are unrelated by design, and that independence is exactly what makes their comparison useful.

 

Can casing pressure ever be higher than tubing pressure?

Yes. On a shut-in well, or on a well with a gas-lifted or thermally loaded annulus, a designed casing pressure can sit above a low flowing tubing pressure. There is no rule that one must always exceed the other: both depend on reservoir condition, fluid properties, completion design and the production operation. What matters is not which number is larger but whether casing pressure starts to track changes in tubing pressure, which would suggest communication between the two spaces.

 

What causes sustained casing pressure to rebuild after bleed-down?

Sustained casing pressure is annular pressure that returns after being bled down and shut in, which shows that fluid or gas is entering the annulus. Common sources are a leaking tubing connection, a failed packer or seal assembly, gas migration through a damaged cement sheath, or pressure communication from a formation. It is defined by that rebuild behaviour rather than by one pressure value, and it is managed under API RP 90-1 for offshore wells and API RP 90-2 for onshore wells.

 

Is casing pressure the same as formation pressure?

No. Casing pressure is read at the top of the annulus, separated from the reservoir by the annulus fluid column, the packer and the cement sheath. Estimating formation pressure from that gauge requires the fluid gradient and an assumption about barrier integrity, so the relationship is indirect. Treating a casing reading as pore pressure is one of the most common interpretation errors in well surveillance.

 

What is the difference between annular pressure buildup and sustained casing pressure?

Annular pressure buildup (APB) is a rise in a confined annulus when trapped fluid expands as temperature increases; it normally stabilises once temperature settles and is often a designed condition. Sustained casing pressure rebuilds after venting and is not explained solely by temperature or deliberate injection. A controlled bleed-down and observation test separates the two, and the classification follows API RP 90-1 or 90-2 depending on location.

 

Which pressure rating governs tubing design and which governs casing?

Burst, or internal yield, normally governs tubing, driven by maximum shut-in surface pressure with a gas column plus any injection or stimulation pressure. Casing reverses the priority: collapse from external pressure typically governs, because the annulus fluid level and formation loads act inward on the string. Both collapse and burst ratings are calculated under API TR 5C3 and quoted in the pipe specification, and both should be checked for the specific well design.

 

What do the A, B and C annuli refer to on a wellhead?

Annuli are named from the inside out. The A annulus is the space between the production tubing and the innermost casing, normally sealed by the packer below and the tubing hanger at surface; the B annulus lies between that casing and the next string, and the C annulus between the next strings. Because ‘casing pressure’ is ambiguous on a multi-string well, reports should always name which annulus a reading comes from rather than quoting an unlabelled value.

 

What guidance does API RP 90 give for annular pressure?

API RP 90-1 addresses offshore wells and API RP 90-2 onshore wells. They set out how to classify annular pressure by source — thermal, operator-imposed, trapped during cementing, or formation-induced — and how to manage each category. Many operators screen readings against a percentage of the casing minimum internal yield or burst rating, but the actual limit is set by company policy and the regulator and varies by region and well type, so a single percentage should not be carried across a portfolio.

Home Tel Mail Inquiry